各位大大 不好意思 冒昧請問一下
小弟有一台 BACHMANN DYNAMIS 剛買約1個月 很少玩 最近要玩時
接收部分 電源燈(左)快速閃爍 信號燈(右)約一秒閃一下 遙控器無法控制(遙控器的信號沒格) 請問不知道有沒有大大知道說哪邊有問題
或是可以幫我測試看看說是否有哪邊壞掉 或是設定上的問題 我住台中 感恩
BACHMANN DYNAMIS DCC 控制器
-
- 三等資深會員
- 文章: 309
- 註冊時間: 2007-01-29 10:53
- 來自: 台中市
參考看看
這款是紅外線的有指向性,要對著接收端一下喔!不然就會像您這樣閃燈,可以看一下說明書有說明燈號代表意義
我把它拍成影片 請大大幫幫忙 感恩鄭瑞清 寫:是否可以拍照來看看是什麼問題...
如果控制器沒格,是沒有辦法控制的..
http://www.youtube.com/watch?v=aHRBq1gnboI
-
- 三等資深會員
- 文章: 309
- 註冊時間: 2007-01-29 10:53
- 來自: 台中市
請參考以下:
I cannot get my System to communicate; the LEDs in the base station keep flashing?
Answer
i) Firstly when you have switched your system on, have you pressed the Emergency Stop button to allow the system to optimise? Until you press the Emergency stop button the Hand Set and the Base station will not communicate with each other. ii) If you have used the system previously and the system is not communicating check that the Edit Remote ID and the Edit base ID are both set to O. You will find these settings in the System Menu section and can be very easily altered. [MENU] -> [LEFT ARROW] ->to reach SYSTEM MENU press [TICK] shows EDIT BASE ID which should be 0. If not, then press [TICK], enter 0 and press [TICK] to save the value and come out of the menu. Then power down the entire system and back up again, basetation first.
I cannot get my System to communicate; the LEDs in the base station keep flashing?
Answer
i) Firstly when you have switched your system on, have you pressed the Emergency Stop button to allow the system to optimise? Until you press the Emergency stop button the Hand Set and the Base station will not communicate with each other. ii) If you have used the system previously and the system is not communicating check that the Edit Remote ID and the Edit base ID are both set to O. You will find these settings in the System Menu section and can be very easily altered. [MENU] -> [LEFT ARROW] ->to reach SYSTEM MENU press [TICK] shows EDIT BASE ID which should be 0. If not, then press [TICK], enter 0 and press [TICK] to save the value and come out of the menu. Then power down the entire system and back up again, basetation first.
看你的影片,發現你把主機放在鍵盤上而控制器放在桌上,哆啦~ 寫:我把它拍成影片 請大大幫幫忙 感恩鄭瑞清 寫:是否可以拍照來看看是什麼問題...
如果控制器沒格,是沒有辦法控制的..
http://www.youtube.com/watch?v=aHRBq1gnboI
這樣會接受不到訊號,你可以控制器的前端對準主機的接受端,
再看有沒有訊號...
如果還不行,可能就要找賣你的廠商了...
-
- 三等資深會員
- 文章: 309
- 註冊時間: 2007-01-29 10:53
- 來自: 台中市